PRTG Manual: SNMP Custom String v2 Sensor

Enabled Beta Sensors experimental feature

This sensor requires that the Beta Sensors experimental feature is enabled.

For more information, see the Knowledge Base: What are beta sensors and how can I use them?

Credentials

This sensor requires credentials for SNMP in settings that are higher in the object hierarchy.

IPv6

This sensor supports IPv6.

Performance impact

This sensor has a very low performance impact.

Lookups

This sensor uses lookups to determine the status values of one or more channels.

Scanning interval

This sensor has a fixed minimum scanning interval for performance reasons. You cannot use a shorter scanning interval. Consequently, shorter scanning intervals in the Monitoring settings are not available for this sensor.

• The minimum scanning interval of this sensor is 1 minute.
• The recommended scanning interval of this sensor is 1 minute.

Knowledge Base

Knowledge Base: How do I find out which OID I need for an SNMP Custom sensor?

OID

Enter the OID of the object that you want to monitor. You can enter the numeric OID or the symbolic name. If you use the symbolic name, enter its full path. For example, iso.org.dod.internet.mgmt.mib-2.host.hrSystem.hrSystemUptime.hrSystemUptime.

Search String

Enter the string that you want to search for.

This setting is case-sensitive.

Interpret Result As

Define the type of the received string:

• String (default): Handle the result as a string. No interpretation takes place.
• MAC address: Interpret the SNMP value returned by the OID as a MAC address. If you select this option, make sure to enter the MAC address with lowercase characters and use hyphens as separators in the Search String settings. For example, ab-cd-12-34-56-78.
• IPv4 address: Interpret the SNMP value returned by the OID as an IPv4 address.

Sensor Behavior

Select how the sensor reacts based on the result of the string search:

• Do not change sensor status (default): The result of the string search does not affect the sensor status.
• Show down status if string is not found: Show the Down status if the string is not found.
• Show down status if string is found: Show the Down status if the string is found.
• Show warning status if string is not found: Show the Warning status if the string is not found.
• Show warning status if string is found: Show the Warning status if the string is found.

Primary Channel

Select a channel from the list to define it as the primary channel. In the device tree, PRTG displays the last value of the primary channel below the sensor's name. The available options depend on what channels are available for this sensor.

You can set a different primary channel later by clicking below a channel gauge on the sensor's Overview tab.

Graph Type

Define how this sensor shows different channels:

• Show channels independently (default): Show a graph for each channel.
• Stack channels on top of each other: Stack channels on top of each other to create a multi-channel graph. This generates a graph that visualizes the different components of your total traffic.
  You cannot use this option in combination with manual Vertical Axis Scaling (available in the channel settings).

Stack Unit

This setting is only visible if you select Stack channels on top of each other above.

Select a unit from the list. PRTG stacks all channels with this unit on top of each other. By default, you cannot exclude single channels from stacking if they use the selected unit. However, there is an advanced procedure to do so.

Result Handling

Define what PRTG does with the sensor result:

• Discard result (default): Do not store the sensor result.
• Store result: Store the sensor result and the last response in the \Logs\sensors subfolder of the PRTG data directory on the probe system. The file name is Result of Sensor [ID].log. This setting is for debugging purposes. PRTG overwrites this file with each scanning interval.

This option is not available when the sensor runs on the hosted probe of a PRTG Hosted Monitor instance.

In a cluster, PRTG stores the result in the PRTG data directory of the master node.

Downtime

In the channel table on the Overview tab, this channel never shows any values. PRTG uses this channel in graphs and reports to show the amount of time in which the sensor was in the Down status.

Response Time

The response time

This channel is the primary channel by default.

String Found

If the search string is found in the SNMP value returned by the OID

The channel status and the displayed value type depend on the Sensor Behavior setting. If you select Do not change sensor status (default), the sensor displays a value of 1 in channel if the search string is found. Otherwise, the displayed value is determined via lookup.