PRTG Manual: SNMP Buffalo TS System Health Sensor
The SNMP Buffalo TS System Health sensor monitors the system health of a Buffalo TeraStation network-attached storage (NAS) via the Simple Network Management Protocol (SNMP).
This sensor supports the following TeraStation systems: 3000, 3010, 3020, 5000, 5010, 6000, and 7000 series.
Run an auto-discovery with the device template Buffalo TeraStation NAS to automatically create SNMP Custom Table sensors with additional useful information about the TeraStation, for example, array status, disk smart status, disk status, and Internet Small Computer System Interface (iSCSI) status. This device template also creates SNMP sensors for traffic, memory, and load average on the TeraStation.
For a detailed list and descriptions of the channels that this sensor can show, see section Channel List.
- Dutch: SNMP Buffalo TS Systeemstatus
- French: Buffalo TS état du système (SNMP)
- German: SNMP Buffalo TS System Health
- Japanese: SNMP Buffalo TS システムの正常性
- Portuguese: Funcionamento do sistema Buffalo TS (SNMP)
- Russian: Работоспособность системы Buffalo TS по SNMP
- Simplified Chinese: SNMP Buffalo TS 系统健康状况
- Spanish: Salud de sistema Buffalo TS (SNMP)
- This sensor supports the TeraStation 3000, 3010, 3020, 5000, 5010, 6000, and 7000 series.
- This sensor supports IPv6.
- This sensor has a low performance impact.
- This sensor uses lookups to determine the status values of one or more channels.
- This sensor has predefined limits for several metrics.
- In certain cases, this sensor might show an error message. If this occurs, open the settings of the parent device, section SNMP Compatibility Options, and set the Walk Mode to Use GETNEXT requests.
Setting |
Description |
---|---|
Sensor Name |
Enter a name to identify the sensor. By default, PRTG shows this name in the device tree, as well as in alarms, logs, notifications, reports, maps, libraries, and tickets.
|
Parent Tags |
The tags that the sensor inherits from its parent device, parent group, and parent probe.
|
Tags |
Enter one or more tags. Confirm each tag with the Spacebar key, a comma, or the Enter key. You can use tags to group objects and use tag-filtered views later on. Tags are not case-sensitive. Tags are automatically inherited.
The sensor has the following default tags that are automatically predefined in the sensor's settings when you add the sensor:
|
Priority |
Select a priority for the sensor. This setting determines the position of the sensor in lists. The highest priority is at the top of a list. Choose from the lowest priority ( |
Setting |
Description |
---|---|
Primary Channel |
Select a channel from the list to define it as the primary channel. In the device tree, the last value of the primary channel is always displayed below the sensor's name. The available options depend on what channels are available for this sensor.
|
Graph Type |
Define how different channels are shown for this sensor:
|
Stack Unit |
This setting is only visible if you select Stack channels on top of each other above. Select a unit from the list. All channels with this unit are stacked on top of each other. By default, you cannot exclude single channels from stacking if they use the selected unit. However, there is an advanced procedure to do so. |
By default, all of these settings are inherited from objects that are higher in the hierarchy. We recommend that you change them centrally in the root group settings if necessary. To change a setting for this object only, click under the corresponding setting name to disable the inheritance and to display its options.
For more information, see section Inheritance of Settings.
For more information, see section Root Group Settings, section Scanning Interval.
Schedules, Dependencies, and Maintenance Window
You cannot interrupt the inheritance for schedules, dependencies, and maintenance windows. The corresponding settings from the parent objects are always active. However, you can define additional schedules, dependencies, and maintenance windows. They are active at the same time as the parent objects' settings.
For more information, see section Root Group Settings, section Schedules, Dependencies, and Maintenance Window.
For more information, see section Root Group Settings, section Access Rights.
Which channels the sensor actually shows might depend on the target device, the available components, and the sensor setup.
Channel |
Description |
---|---|
1 Min CPU Load Average |
The average CPU load (%) |
Available Memory |
The available memory |
Downtime |
In the channel table on the Overview tab, this channel never shows any values. PRTG uses this channel in graphs and reports to show the amount of time in which the sensor was in the Down status |
Errors |
The number of errors
|
Failover Status |
The failover status
|
Firmware Update Available |
If a firmware update is available
|
Percent Available Memory |
The available memory (%) |
Uptime |
The uptime |
Warnings |
The number of warnings
|
KNOWLEDGE BASE
What security features does PRTG include?
My SNMP sensors don’t work. What can I do?