Device and Sensor Setup > Sensor Settings

PRTG Manual: SNMP HPE ProLiant System Health Sensor

The SNMP HPE ProLiant System Health sensor monitors the system health of an HPE ProLiant server via the Simple Network Management Protocol (SNMP).

SNMP HPE ProLiant System Health Sensor

For a detailed list and descriptions of the channels that this sensor can show, see section Channel List.

Sensor in Other Languages

Dutch: SNMP HPE ProLiant Systeemstatus
French: HPE ProLiant état du système (SNMP)
German: SNMP HPE ProLiant Systemzustand
Japanese: SNMP HPE ProLiant システム正常性
Portuguese: Funcionamento do sistema HPE ProLiant (SNMP)
Russian: Работоспособность системы HPE ProLiant по SNMP
Simplified Chinese: SNMP HPE ProLiant 系统健康状况
Spanish: Salud de sistema HPE ProLiant (SNMP)

Remarks

For Gen10 servers: Use the HPE Integrated Lights Out (iLO) interface as the parent device.

For Gen9 servers or earlier: This sensor requires HPE Insight Management Agents and HPE Insight Management WBEM Providers on the target system.

This sensor supports iLO as of iLO 3. We recommend that you use at least iLO 4.

This sensor supports IPv6.

This sensor has a low performance impact.

This sensor uses lookups to determine the status values of one or more channels.

This sensor has predefined limits for temperatures and broken frames.

Redundant array of independent disks (RAID) controllers that have no hard disks assigned might cause the Down status. In this case, deactivate the respective controllers in the HPE ProLiant BIOS to avoid sensor errors.

Detailed Requirements

Requirement	Description
HPE system management tools	For Gen9 servers or earlier, this sensor requires a specific HPE system management tool to be installed on the target system to report data via SNMP: HPE Insight Management Agents. To receive SNMP data from redundant array of independent disks (RAID) controllers, the sensor also requires HPE Insight Management Agents. For Gen10 servers, this sensor no longer requires HPE system management tools. For more information and download links, see the Knowledge Base: Monitor HP ProLiant via SNMP? For Gen9 servers or earlier, some of the HPE object identifiers (OID) that this sensor uses are only accessible via the iLO interface. If this sensor throws an error that it cannot find "such device types", create a device that points to the address of the HPE iLO interface (if available) and add the sensor to this device. We recommend that you use the Agentless Management feature with configured SNMP. You can set this up in the iLO configuration interface under Administration \| Management \| SNMP Settings. For Gen10 servers, use the HPE iLO interface as parent device for this sensor.

Requirement

Description

HPE system management tools

For Gen9 servers or earlier, this sensor requires a specific HPE system management tool to be installed on the target system to report data via SNMP: HPE Insight Management Agents. To receive SNMP data from redundant array of independent disks (RAID) controllers, the sensor also requires HPE Insight Management Agents. For Gen10 servers, this sensor no longer requires HPE system management tools.

For more information and download links, see the Knowledge Base: Monitor HP ProLiant via SNMP?

For Gen9 servers or earlier, some of the HPE object identifiers (OID) that this sensor uses are only accessible via the iLO interface. If this sensor throws an error that it cannot find "such device types", create a device that points to the address of the HPE iLO interface (if available) and add the sensor to this device. We recommend that you use the Agentless Management feature with configured SNMP. You can set this up in the iLO configuration interface under Administration | Management | SNMP Settings. For Gen10 servers, use the HPE iLO interface as parent device for this sensor.

Basic Sensor Settings

Setting	Description
Sensor Name	Enter a name to identify the sensor. By default, PRTG shows this name in the device tree, as well as in alarms, logs, notifications, reports, maps, libraries, and tickets. If the name contains angle brackets (<>), PRTG replaces them with braces ({}) for security reasons. For more information, see the Knowledge Base: What security features does PRTG include?
Parent Tags	The tags that the sensor inherits from its parent device, parent group, and parent probe. This setting is for your information only. You cannot change it.
Tags	Enter one or more tags. Confirm each tag with the Spacebar key, a comma, or the Enter key. You can use tags to group objects and use tag-filtered views later on. Tags are not case-sensitive. Tags are automatically inherited. It is not possible to enter tags with a leading plus (+) or minus (-) sign, nor tags with parentheses (()) or angle brackets (<>). For performance reasons, it can take some minutes until you can filter for new tags that you added. The sensor has the following default tags that are automatically predefined in the sensor's settings when you add the sensor: snmphpesystemhealthsensor systemhealth snmphpe hpe
Priority	Select a priority for the sensor. This setting determines the position of the sensor in lists. The highest priority is at the top of a list. Choose from the lowest priority () to the highest priority ().

Sensor Display

Setting	Description
Primary Channel	Select a channel from the list to define it as the primary channel. In the device tree, the last value of the primary channel is always displayed below the sensor's name. The available options depend on what channels are available for this sensor. You can set a different primary channel later by clicking below a channel gauge on the sensor's Overview tab.
Graph Type	Define how different channels are shown for this sensor: Show channels independently (default): Show a graph for each channel. Stack channels on top of each other: Stack channels on top of each other to create a multi-channel graph. This generates a graph that visualizes the different components of your total traffic. You cannot use this option in combination with manual Vertical Axis Scaling (available in the channel settings).
Stack Unit	This setting is only visible if you select Stack channels on top of each other above. Select a unit from the list. All channels with this unit are stacked on top of each other. By default, you cannot exclude single channels from stacking if they use the selected unit. However, there is an advanced procedure to do so.

Setting

Description

Primary Channel

Select a channel from the list to define it as the primary channel. In the device tree, the last value of the primary channel is always displayed below the sensor's name. The available options depend on what channels are available for this sensor.

You can set a different primary channel later by clicking below a channel gauge on the sensor's Overview tab.

Graph Type

Define how different channels are shown for this sensor:

Show channels independently (default): Show a graph for each channel.
Stack channels on top of each other: Stack channels on top of each other to create a multi-channel graph. This generates a graph that visualizes the different components of your total traffic.
You cannot use this option in combination with manual Vertical Axis Scaling (available in the channel settings).

Stack Unit

This setting is only visible if you select Stack channels on top of each other above.

Select a unit from the list. All channels with this unit are stacked on top of each other. By default, you cannot exclude single channels from stacking if they use the selected unit. However, there is an advanced procedure to do so.

Inherited Settings

By default, all of these settings are inherited from objects that are higher in the hierarchy. We recommend that you change them centrally in the root group settings if necessary. To change a setting for this object only, click under the corresponding setting name to disable the inheritance and to display its options.

For more information, see section Inheritance of Settings.

Scanning Interval

For more information, see section Root Group Settings, section Scanning Interval.

Schedules, Dependencies, and Maintenance Window

You cannot interrupt the inheritance for schedules, dependencies, and maintenance windows. The corresponding settings from the parent objects are always active. However, you can define additional schedules, dependencies, and maintenance windows. They are active at the same time as the parent objects' settings.

Schedules, Dependencies, and Maintenance Window

For more information, see section Root Group Settings, section Schedules, Dependencies, and Maintenance Window (default).

Access Rights

For more information, see section Root Group Settings, section Access Rights.

Channel Unit Configuration

Which channel units are available depends on the sensor type and the available parameters. If no configurable channels are available, this field shows No configurable channels.

Channel Unit Configuration

For more information, see section Root Group Settings, section Channel Unit Configuration.

Channel List

Which channels the sensor actually shows might depend on the target device, the available components, and the sensor setup.

Channel	Description
CPU Fan Status	The CPU fan status Up status: OK Warning status: Degraded Down status: Failed Unknown status: Other
Disk Controller Status	The disk controller status Up status: OK Warning status: Degraded Down status: Failed Unknown status: Other
Downtime	In the channel table on the Overview tab, this channel never shows any values. PRTG uses this channel in graphs and reports to show the amount of time in which the sensor was in the Down status
Fans Broken	The number of broken fans This channel has a default limit Upper error limit: 0
Fans Running	The number of running fans
Fault Tolerant Fans Broken	The number of fault-tolerant broken fans This channel has a default limit Upper error limit: 0
Fault Tolerant Fans Running	The number of fault-tolerant running fans
Overall Status	The overall status Up status: OK Warning status: Degraded Down status: Failed Unknown status: Other This channel is the primary channel by default.
Power Consumption [#]	The power consumption
Power Consumption [#] (%)	The power consumption (%)
Power Supply [#] Condition	The power supply condition Up status: OK Down status: Degraded, Failed Unknown status: Other
Power Supply [#] Status	The power supply status Up status: No Error Down status: Bist Failure, Brownout, Calibration Table Invalid, Dac Failure, Eprom Failure, Fan Failure, General Failure, Give Up On Startup, Interlock Open, No Power Input, Nvram Invalid, Orring Diode Failed, Ram Test Failed, Temp Failure, Voltage Channel Failed, Vref Failure
System Fan Status	The system fan status Up status: OK Warning status: Degraded Down status: Failed Unknown status: Other
Temperature [#] ([Component])	The temperature of the component
Thermal Status	The thermal status Up status: OK Warning status: Degraded Down status: Failed Unknown status: Other

KNOWLEDGE BASE

Monitor HP ProLiant via SNMP?

https://kb.paessler.com/en/topic/33133

What security features does PRTG include?

https://kb.paessler.com/en/topic/61108

Why is my SNMP HPE ProLiant System Health sensor in the error status after updating PRTG?

https://kb.paessler.com/en/topic/61805

My SNMP sensors don’t work. What can I do?

https://kb.paessler.com/en/topic/46863

Previous Next

PRTG Manual: SNMP HPE ProLiant System Health Sensor

Take Your Monitoring to the Next Level

Take Your
Monitoring
to the
Next Level